These are included in the pattern for the Endless Hearts Braid with Corner. I just didn't want them to slip by unnoticed. 😉
This post is actually a tribute to my test tatters. I had nine test tatters, and they came up with many different ways to do the various elements in the pattern!
I incorporated some of their suggestions, but not others. However, now that I realise what a wide variety there is in tatting styles, I want to share their ideas with all of you – because you may also have the same style.
I will probably update this post as and when I come across more suggestions or links...
All the variations suggested below make reference to the pattern for the Endless Hearts Braid with Corner
 |
Make a vsp on Chain (2). Don't join Chain (2) to Ring (1) yet. Tat Chain (3) until the point of the EPJ. As with a normal picot join, pull a loop of thread up through the picot of Ring (1), but then pull it down through the vsp on Chain (2). Put the shuttle through the loop and snug up, but not too tightly. Later, join Ring (4) into a loop of the EPJ.
A. Make an FIP instead of a vsp on Chain (2). Then pull up the loop through both the FIP and the picot of Ring (1), put the shuttle through the loop, and snug up.
B. Make an IP instead of a vsp on Chain (2). Then pull up the loop through both the IP and the picot of Ring (1), put the shuttle through the loop, and snug up.
C. Make a long picot on Ring (1). Make a vsp on Chain (2), do not join to Ring (1). When tatting Chain (3), make a picot join into the long picot of Ring (1) and the vsp of Chain (2) (the vsp is layered over the long picot), put the shuttle through the loop and snug up. Later, when tatting Ring (4), make a picot join into the long picot of Ring (1). (This works best if doing the pattern front-side/back-side.) (More details here.)
D. UPDATE 27 August 2023: Recently, in Craftree, Anne Fairchild (user @ymarsquirtle) introduced us to the Skylark Join. It looks like a CWJ from the front, but it's easier to do, and if the picot on the ring below is long enough, it can be pulled through and joined to the next element. So, for this pattern: make a long picot on Ring (1); join Chain (2) to Ring (1) with a Skylark Join and pull the Ring (1) picot up; join Chain (3) into the long picot of Ring (1). Supposing you use a Lark's Head Picot Join for this, I am wondering if Ring (4) can later be joined into the Ring (1) long picot as well. I'd have to try this... :-) 1 September 2023: Anne Fairchild (@ymarsquirtle) has now tried this! Her example looks fantastic :-D (https://craftree.com/projects/5114)
A. Make a lock join from Chain (2) into the picot of Ring (1). Then, later, do a picot join from Chain (3) into the lock join on Chain (2). Then, later, join Ring (4) into the core thread of Chain (3).
B. On Chain (2), make a CWJ into the Ring (1) picot; also make a vsp between the half-stitches of the CWJ. Then, later, do a picot join from Chain (3) into the vsp on the CWJ on Chain (2), and immediately make an FIP on Chain (3). Then, later, join Ring (4) into the FIP. (Two of my test tatters independently came up with this solution.)
C. If you don't mind strivers (safety pins / paper clips): On Ring (1), make a tiny picot. On Chain (2), make a CWJ into Ring (1), and put a striver between the legs of the CWJ. On Chain (3), make a picot join where the striver is, then immediately put the striver on the core thread. Then join Ring (4) with a picot join into Chain (3) where the striver is.
In the pattern, the turn is accomplished with two first-half stitches. Other ways are:
A. Simply RW the pattern around the chain being tatted. (This was my original suggestion; it did not work too well during test tatting.)
B. Do a SLT, then RW.
C. Use a Reverse Join where joining to the previous clover (video tutorial here) (However, this will lock the core thread.)
A. the Anne Dyer Join to the Smooth Side (or JSS) (video tutorial here)
B. the Slope & Roll Join (this can break the line of caps for the chain)
C. the lock join (this will put a dimple in the chain)
D. UPDATE 27 August 2023: Change the CWJ to a Skylark Join (see above).
A. The Intruding Picot (as mentioned above)
B. The down picot (tutorial here)
B. Making the 14 ds stretches of chain a bit longer - 16 or 18 ds.
C. Omitting free picots from the rings.
This is a pattern I was working on quite intensely, in early 2013. In response to a request, I even created an SCMR corner for it.
But then I stalled, because it was so onerous to tat! I needed two paper clips as strivers for every repeat of the pattern – they went on, then off, then on, then off, over and over again.
When it came to describing how to tat it – well, that was even more hideous! I took pictures for a tutorial, then realised that I still needed to write long and convoluted sentences about joining to the undersides of chains…
So, I just gave up – though I did go on to write up and publish other patterns using the little hearts (see under "My patterns").
But, in July, Muskaan shared about the Intruding Picot. I saw at once that maybe this picot could replace those pesky paper clips. So I dusted off my Endless Hearts samples and scribbles and started experimenting with it again. I eventually stumbled on a join that was new to me – I call it the Encapsulating Picot Join. That solved most of my problems, and I was able to tat the Endless Hearts without strivers or tears, and then to write it up and draw diagrams for it.
And now, after extensive test-tatting and rewrites, here it is at last!
My test tatters made many suggestions, reflecting a great array of tatting styles! I wasn't able to use them all, but I have compiled them in the next blog post, so that you can try them out, if you wish.
